Residential Slope Roofs

The Ridgepro Roof Attachment Tool is the ultimate Roof Safety System. It's been specially designed to get you safely from the ladder to the peak and back. The main body is constructed of high-grade aluminum capable of withstanding thousands of pounds of pulling force. The RIDGEPRO features an adjustable pitch-selection grid with an incremental range of 6/12 to 12/12 with pitches etched into the main body. The two padded cross members protect existing surface material from damage and balance...

For use on roofs from flat to 12/12 pitch, wood or metal. 5000 lb. anchor point. Fasteners included. Tested and approved for metal roofing applications, minimum 20 gauge metal or thicker, attached directly onto the surface. For metal installation: use (16) screws (8 per side), 6 in center column of fastener installation holes, in 1 hole left of center and 1 hole right of center. Guardian recommends HILTI Kwik-Pro self-drilling screws. Features: Designed for temporary use on wood rooftopsFits...

Most roof anchor installations require the removal of shingles to install. This can pose a problem, especially on older roofs with brittle shingles. No need to remove the ridge cap to install fall arrest anchors because this flashing allows you to install anchors directly over your existing roofing material. The D- Minus anchor can be mounted directly over existing asphalt shingle roofs without removing any shingles.  To cover the anchor and fasteners and protect it from the elements we...

The PitchPro is a premier fall protection anchor designed for sloped-roof asphalt shingle construction. The PitchPro is the perfect solution for both new and existing construction, and its low-profile installation makes it an excellent choice for permanent applications. Its oversized connection point makes attaching and detaching easy and bind-free. Made from robust powder-coated steel, the PitchPro resists damage from repeated installations, and ensures the longest possible lifespan. Feat...

The Guardian Fall Protection Snappy Anchor is a disposable anchorage connector designed to fit a wide variety of wood roof pitches. The Snappy is convenient, easy to install and remove, and meets all applicable OSHA regulations. To use, simply adjust the Snappy to fit over selected roof ridge, then nail into roof truss using all fastener installation holes. Supplied with all necessary fasteners. Features:  Single UseCan be bent to fit any roof pitch Convenient and disposable Easy to...

The D-Minus anchor is our most economical fall arrest anchor and is available in gray powder coated 11-gauge mild steel or 11-gauge 430 stainless steel. Installs with 6 factory supplied stainless steel spiral shank nails or an optional #12 screws. This anchor is specified for use on asphalt shingle roofing and is low profile making them difficult to notice on the roof. This anchor can be used for new construction, reroof or retrofitting onto existing roofs. In addition, this anchor can be used...

Single D-ring, Permanent Roof Anchor with Stainless Steel Body; Fastens Under Shingles, Leaving D-ring Exposed for Attachment; 19" Including D-ring with 17" Nailing Surface. Features:  Designed for under-tile roof ridge or field installationFeatures 17" stainless steel nailing plate with 2" connecting D-ring.Includes 16D stainless steel nails for installation to wood roof structuresMeets OSHA 1926.502 regulations Please read and understand the manufacturer instructions before using this...

The RS-20 anchor is a permanent roof anchor designed specifically for tile, slate, wood and synthetic roofing materials. The 20” long strap allows you to adjust the reveal of the D-ring for your specific roofing material and the unique design of the anchor also allows you to physically bend the D-ring portion of the anchor up and over the tile or slate so that it lays flat on the surface. This permanent, low profile anchor comes with stainless steel attachment hardware and comprehensive...

The Moveable ARS Anchor follows the same design principles as our ARS Permanent Roof Anchors. This is designed for the framing tradesmen that need a quick, easy anchorage connector for their lanyards, lifelines or SRL’s. Made from 11-gauge steel that is powder coated. Comes with a 3/8” stainless steel detent pin with elastic tether. Heavy Duty 11-gauge steel construction2 models cover 2×4 trussesStainless Steel locking detent pinRated for OSHA Fall ArrestPowder Coated for Durability Please...

The Guardian Fall Protection Halo Anchor is a temporary and reusable roof anchorage connector. It is composed of 1/4 inch thick steel, a zinc-plated forged alloy steel O-ring, and can support loads up to 5,000 pounds. It may be used in both Fall Arrest and Restraint applications, and is supplied with all necessary fasteners. FEATURES: Removable/Reusable 1/4" thick steel roof anchorComplete with zinc plated forged alloy steel O-ringNail or bolt into the roof member)Designed to be removable, it...

For use on wood framed structures that can be mounted at the ridge or in the field. Can be installed with nails (supplied) or screws and used to connect your vertical lifeline, SRL or lanyard to for fall protection. Made from 11-gauge zinc coated steel. Replacement anchor for many fall protection kits/buckets found in the market today.Features:  Industry Standard Design with Hinged D-RingUse up to a 20/12 Pitch or Flat on the DeckRated for OSHA 5,000 pounds Fall ArrestInstall with Nails...

Double D-ring; Permanent Roof Anchor with Stainless Steel Body; Fastens Under Shingles, Leaving D-rings Exposed for Attachment; 17" Including D-rings with 12" Nailing Surface. Features: Designed for installation under roof ridge capFeatures 12" stainless steel nailing plate with 2-1/4" connecting D-rings.Includes 16D stainless steel nails for installation to wood roof structuresMeets OSHA 1926.502 regulations Please read and understand the manufacturer instructions before using this product. ...

The Guardian Fall Protection Ridge-It Anchor line is designed for permanent use on wood rooftops. This Ridge-It model RIDG-1 is manufactured with a D-ring on one end and is 9—3/4" long, while the RIDG-2 is manufactured with 2 D-ring ends, and is 18" long. Ridge-It Anchors are composed highly durable stainless steel and zinc-plated steel, and are compliant with all applicable OSHA regulations. Ridge-It Anchors are easy to install, and are ideal for both residential construction and maintenance...

The 30° angle fixed length, factory engineered Horizontal Lifeline System is for use by 3 workers in fall restraint or 2 in fall arrest. This system is available in a 20’ kit with or without a carry bag. This 3rd party engineered horizontal line kit is a cost-effective way to have multiple workers on the roof with room to move freely. Engineering standards specify that a horizontal lifeline without an energy absorbing device subjected to fall hazards must have a 30° anchors between anchorage...

#1 selling anchor for reroof, new construction and remodeling. The low-profile design is aesthetically pleasing and is designed to last the life of the structure. The Retro-Fit is designed to give all who access the roof a reliable tie-off point. Installs with just 8 nails and comes with special butyl waterproof flashing strips to seal the stainless-steel nails. Fabricated with 430 stainless steel and certified for over 5,000 pounds. Use over asphalt shingle, wood shake or metal roofing, the...

The Reusable Roof Anchor is built with durable zinc steel and is ideal for temporary use on wood or metal roofs. The anchor hinge design allows it to be screwed or nailed in position on roofs ranging from flat to sheer. Features:  Installed on peak or flat wood and metal decking roofs.Hinged construction for adjustment to different angles.Corrosion-resistant plated steel.Large D-Ring connection point.Fasteners NOT included.   ...

Combo Safety Bar for 2×4 and 2×6 trusses The Safety Bar is a unique fall protection anchor for use while working with open truss situations. It spans 3 trusses and locks in securely with detent pins while gauging the trusses 24” on center. 2 users and tie off to the safety bar with the use of a shock absorbing lanyard or SRL’s. Our Safety Bar is the only product on the market for open framing fall protection and is used by framing crews across the country for OSHA compliance during the...

FallTech's Ringed Plate Anchor provides a temporary safety solution for workers performing work on building exteriors and roofs. Installed over a truss on the field of wood frame structures, the Ringed Plate Anchor serves as a single user point for personal fall arrest and restraint systems. The fallTech Ringed Plate Anchor is ideal for use during tasks such as painting, siding, roofing, window cleaning, or general construction Features: Temporary fall protection for residential and light...

The Guardian Fall Protection Ridge-It Anchor line is designed for use on wood rooftops. This Ridge-It model RIDG-1 is manufactured with a D-ring on one end and is 9—3/4" long, while the RIDG-2 is manufactured with 2 D-ring ends, and is 18" long. Ridge-It Anchors are composed highly durable stainless steel and zinc-plated steel, and are compliant with all applicable OSHA regulations. Ridge-It Anchors are easy to install, and are ideal for both residential construction and maintenance...

Single-Use roof anchor with nails features user fold-bend to fit roof peaks. Single-use temporary anchor can be removed or hammered down.  Features 6" x 1-1/2" bend-in-place nailing plates with 3/4" connecting eyeIncludes 16D nails for roof ridge installation.For temporary use on wood structuresMeets OSHA 1926.502 regulations

The 30° angle fixed length, factory engineered Horizontal Lifeline System is for use by 3 workers in fall restraint or 2 in fall arrest. This system is available in a 20’ kit with or without a carry bag. This 3rd party engineered horizontal line kit is a cost-effective way to have multiple workers on the roof with room to move freely. Engineering standards specify that a horizontal lifeline without an energy absorbing device subjected to fall hazards must have a 30° anchors between anchorage...

Designed for production builders who want a robust anchor point during the framing and construction of the home but do not want to leave anything permanently attached to the structure. The decking is installed over the top of the anchor but the tie off straps stay exposed to the outside protecting all trades from fall hazards. It can also be utilized in a similar fashion to the Safety Bar. Here is how it works: Install the Truss Bar onto truss at predetermined locationsUse for fall protection...

Tie-Off Straps are made from 2” wide polyester or nylon and are designed for use as temporary anchorage points to connect vertical lifelines, SRL’s, web lanyard and rope lanyards. Use on wood, steel and concrete structures. Tie-Off straps are wrapped, cinched around the structure to make for a secure anchor or can be embedded into concrete and evacuated when finished with the job. Please see the part number list below for Application, Length, Compliance and Packaging information for all our...

The Guardian Fall Protection Truss Boss Anchor Kit provides everything required for the set-up of a premium roof truss anchor. In addition to a non-corrosive Truss Boss Anchor, this kit also includes waterproof flashing for both composite and tile roofs, and also an anchor cap specially designed to protect the Truss Boss from weather, as well as to not blow off in high winds. The included Truss Boss can be installed on the truss while the truss is still on the ground for additional safety, and...

The anchor can be installed as a retro/reroof application or in new construction on low- and high-profile tile and slate roofing material. This is a double D-ring anchor that measures 40” in between the D-rings which allows them be exposed just under the last course of tile. The unique design does not require a conventional flashing system because the anchor does not penetrate the sheeting. It installs with 8 spiral shank stainless steel nails and includes a butyl flashing strip to provide a...

The new Falltech Chain Roof Anchor, is a highly portable and reusable anchor to be used on residential and commercial wood structures.  The Anchors O-Ring serves as the attachment point for either a PFAS or on HLL system. With it's heavy steel anchoring plates and flexible belted rubber center, the Chain Roof Anchor can be installed either on the ridge or on the field of a roof and may be used on flat or pitched surfaces. The Anchor is Easily installed with nails as a Single-Point anchor...

The PitchPro is a premier fall protection anchor designed for sloped-roof asphalt shingle construction. The PitchPro is the perfect solution for both new and existing construction, and its low-profile installation makes it an excellent choice for permanent applications. Its oversized connection point makes attaching and detaching easy and bind-free. Made from robust powder-coated steel, the PitchPro resists damage from repeated installations, and ensures the longest possible lifespan....

The Malta Dynamics Reusable Roof Anchor is a reusable anchorage connector designed for temporary use on wood rooftops. Our roof anchors fit all roof pitches from flat to 12/12 and their thick-plated steel construction means longer lasting product life. Supplied with all necessary fasteners.Key Features:● Meets OSHA 1910, OSHA 1926 Subpart M, and ANSI A10.32-12● Can be installed with screws or nails● Fits up to 12/12 roof pitch● Fasteners provided● For temporary use on wood rooftops● Worker...

The SafeWaze 360° Roof Anchor is a temporary and reusable fall protection-anchor point, offering a full 360° working radius. Built for use on wood roofs and installs in seconds with the provided fasteners. • 360° Working radius• Zinc Plated Steel (Base), Painted Steel (Connection Point)• (6) 1/4” x 3” in Stainless lag screws for wood installation• Weight capacity: Single person - 310 lbs.(Including person, tools, and materials)• Minimum strength 5,000 lbs.• Meets:OSHA...

Designed specifically for the Metal Building industry, our Super Z-Purlin provides an easy to install anchorage device that includes attachment bolts. The stem height of the anchor is compatible with high rib roofing panels and blanket type insulation. Waterproofing is achieved using a high quality E.P.D.M. gray colored flashing boot and matching stem cover that has an aluminum flange allowing it to be configured easily to any shape panel. The anchor stem features a collapsible design that...

Designed specifically for the Metal Building industry, our Super Z-Purlin provides an easy to install anchorage device that includes attachment bolts. The stem height of the anchor is compatible with high rib roofing panels and blanket type insulation. Waterproofing is achieved using a high quality E.P.D.M. gray colored flashing boot and matching stem cover that has an aluminum flange allowing it to be configured easily to any shape panel. The anchor stem features a collapsible design that...

The Malta Dynamics Single Use Roof Anchor is a handy addition to the roofer’s toolbox. It can be easily bent over the peak of the roof or manipulated to match the pitch of your roof. Because of its versatility and durability, this adjustable pitch anchor creates a reliable tie-off point for your lifeline without causing lasting damage to the rooftop. When installing on the roof, make sure to locate the roof’s crossbeam so that you are anchoring into a strong and solid surface that can support...

Safety Bar Temporary/Reusable Anchor The Safety Bar is a unique fall protection anchor for use while working with open truss situations. It spans 3 trusses and locks in securely with detent pins while gauging the trusses 24” on center. 2 users and tie off to the safety bar with the use of a shock absorbing lanyard or SRL’s. Our Safety Bar is the only product on the market for open framing fall protection and is used by framing crews across the country for OSHA compliance during the absolute...

A permanent roof anchor is a significant part of Personal Fall Arrest Systems (PFAS) and Fall Restraint Systems used while working on roofs. When attached to the ridge of a wooden roof and used with compatible safety systems, this safety anchor helps limit the forces associated with fall arrest. It was built to be used with other components of a PFAS that limit maximum arrest forces to 900 lbs. or less. Designed for wood rooftops and permanent applications, the Malta Dynamics roof safety...

The FrogLink Temporary Roof Anchor is a temporary anchor point with built-in energy absorber and 360° working radius. Ideal for wood roofs. Can be used as a single point anchor or as part of a horizontal lifeline system.FEATURES: Stainless steel construction360° working radiusBuilt-in energy absorber reduces stress & damage to the mounting structureEasily attaches with 7, 14 gauge 75 mm long roofing screws (not included)Single User ...

The Vertical Wall anchors are designed for exterior wall applications as an overhead anchorage device that is nearly invisible from the ground. Fabricated from 11-gauge 430 stainless steel in two models to adapt to varying slope roofs. The install at the wall plate and top chord junction with a single bolt and 4 16d vinyl sinkers that are supplied with each anchor. Perfect for siders, window installers and painters. Can be painted for minimum visual effect. Designed to accommodate the bird...

Features:Rotating anchor maintains proper SRL orientation angle to connected userFeatures adjustable cradle for DuraTech SRLs and other SRL brands up to 60'.SRL cradle includes D-ring for secondary restraint attachmentIncludes 16D nails and 2-1/2" lag screws for over-ridge installationFor temporary reusable applications on pitched wood roof trusses with sheathingMeets OSHA 1926.502 regulations ...

The Form-It is a temporary use roof anchor that can be installed onto a flat surface or a pitched roof. Anchor legs are pre-bent to 25-degrees. Easy to adjust the anchor by hand to match the roof pitch. Installs with 10 of the 16d vinyl sinkers through the sheathing and into a top chord. Maximum exposure time is 6 months from install date. Evacuate by removing or flattening the anchor stem over. Features: Fall Arrest Rated for 5,000 pounds14 gauge zinc plated steelAttached with 10 ea. 16d...

The Flex Chain Anchor is a temporary/reusable anchor that can be installed on wood framed structures with the factory supplied nails or screws. The anchor legs are made from heavy duty 1/4″ zinc plated steel and have a chain with a 3” diameter connector ring. The flex band is made from 6mm rubber belt material. This anchor can be used as a single person anchor or as a horizontal lifeline anchorage point. ¼” Zinc Plated Steel Anchor LegsAdjustable Pitch Roof Anchor3″ Diameter Connector Sliding...

Heavy duty 11-gauge steel reusable anchor that can be installed with nails or screws for fall arrest or fall restraint. Installs at the peak up to a 24/12 pitch, on the surface of the roof deck, or on the floor deck. Can be installed vertically onto a wall system when fastened with our WS Series screws. Comes with 36 ea. duplex nails Adjustable from flat to 20/12 pitchHeavy-Duty 11-gauge SteelDurable Dacromet FinishDual Size Fastener Holes for More OptionsReusable Wood Screws Available ...

The Vertical Wall anchors are designed for exterior wall applications as an overhead anchorage device that is nearly invisible from the ground. Fabricated from 11-gauge 430 stainless steel in two models to adapt to varying slope roofs. The install at the wall plate and top chord junction with a single bolt and 4 16d vinyl sinkers that are supplied with each anchor. Perfect for siders, window installers and painters. Can be painted for minimum visual effect. Designed to accommodate the bird...