Roof Sheathing

For use on roofs from flat to 12/12 pitch, wood or metal. 5000 lb. anchor point. Fasteners included. Tested and approved for metal roofing applications, minimum 20 gauge metal or thicker, attached directly onto the surface. For metal installation: use (16) screws (8 per side), 6 in center column of fastener installation holes, in 1 hole left of center and 1 hole right of center. Guardian recommends HILTI Kwik-Pro self-drilling screws. Features: Designed for temporary use on wood rooftopsFits...

The Guardian Fall Protection Bull Ring Anchors are suitable for personal fall arrest, restraint, or work positioning applications. For all applications, the worker weight capacity range (including all clothing, tools, and equipment) is 130 to 310 pounds. The anchor itself is constructed of 100% zinc-plated steel. Substrate must be roof truss or support beam that is minimum of 3" thick CDX or better. All fasteners (use either six 16d, 3" long 8 gauge nails or three 1/4" x 3" zinc-plated steel...

Most roof anchor installations require the removal of shingles to install. This can pose a problem, especially on older roofs with brittle shingles. No need to remove the ridge cap to install fall arrest anchors because this flashing allows you to install anchors directly over your existing roofing material. The D- Minus anchor can be mounted directly over existing asphalt shingle roofs without removing any shingles.  To cover the anchor and fasteners and protect it from the elements we...

The D-Minus anchor is our most economical fall arrest anchor and is available in gray powder coated 11-gauge mild steel or 11-gauge 430 stainless steel. Installs with 6 factory supplied stainless steel spiral shank nails or an optional #12 screws. This anchor is specified for use on asphalt shingle roofing and is low profile making them difficult to notice on the roof. This anchor can be used for new construction, reroof or retrofitting onto existing roofs. In addition, this anchor can be used...

The Guardian Fall Protection Snappy Anchor is a disposable anchorage connector designed to fit a wide variety of wood roof pitches. The Snappy is convenient, easy to install and remove, and meets all applicable OSHA regulations. To use, simply adjust the Snappy to fit over selected roof ridge, then nail into roof truss using all fastener installation holes. Supplied with all necessary fasteners. Features:  Single UseCan be bent to fit any roof pitch Convenient and disposable Easy to...

Single D-ring, Permanent Roof Anchor with Stainless Steel Body; Fastens Under Shingles, Leaving D-ring Exposed for Attachment; 19" Including D-ring with 17" Nailing Surface. Features:  Designed for under-tile roof ridge or field installationFeatures 17" stainless steel nailing plate with 2" connecting D-ring.Includes 16D stainless steel nails for installation to wood roof structuresMeets OSHA 1926.502 regulations Please read and understand the manufacturer instructions before using this...

The RS-20 anchor is a permanent roof anchor designed specifically for tile, slate, wood and synthetic roofing materials. The 20” long strap allows you to adjust the reveal of the D-ring for your specific roofing material and the unique design of the anchor also allows you to physically bend the D-ring portion of the anchor up and over the tile or slate so that it lays flat on the surface. This permanent, low profile anchor comes with stainless steel attachment hardware and comprehensive...

The Guardian Fall Protection Halo Anchor is a temporary and reusable roof anchorage connector. It is composed of 1/4 inch thick steel, a zinc-plated forged alloy steel O-ring, and can support loads up to 5,000 pounds. It may be used in both Fall Arrest and Restraint applications, and is supplied with all necessary fasteners. FEATURES: Removable/Reusable 1/4" thick steel roof anchorComplete with zinc plated forged alloy steel O-ringNail or bolt into the roof member)Designed to be removable, it...

For use on wood framed structures that can be mounted at the ridge or in the field. Can be installed with nails (supplied) or screws and used to connect your vertical lifeline, SRL or lanyard to for fall protection. Made from 11-gauge zinc coated steel. Replacement anchor for many fall protection kits/buckets found in the market today.Features:  Industry Standard Design with Hinged D-RingUse up to a 20/12 Pitch or Flat on the DeckRated for OSHA 5,000 pounds Fall ArrestInstall with Nails...

Double D-ring; Permanent Roof Anchor with Stainless Steel Body; Fastens Under Shingles, Leaving D-rings Exposed for Attachment; 17" Including D-rings with 12" Nailing Surface. Features: Designed for installation under roof ridge capFeatures 12" stainless steel nailing plate with 2-1/4" connecting D-rings.Includes 16D stainless steel nails for installation to wood roof structuresMeets OSHA 1926.502 regulations Please read and understand the manufacturer instructions before using this product. ...

The Guardian Fall Protection Ridge-It Anchor line is designed for permanent use on wood rooftops. This Ridge-It model RIDG-1 is manufactured with a D-ring on one end and is 9—3/4" long, while the RIDG-2 is manufactured with 2 D-ring ends, and is 18" long. Ridge-It Anchors are composed highly durable stainless steel and zinc-plated steel, and are compliant with all applicable OSHA regulations. Ridge-It Anchors are easy to install, and are ideal for both residential construction and maintenance...

#1 selling anchor for reroof, new construction and remodeling. The low-profile design is aesthetically pleasing and is designed to last the life of the structure. The Retro-Fit is designed to give all who access the roof a reliable tie-off point. Installs with just 8 nails and comes with special butyl waterproof flashing strips to seal the stainless-steel nails. Fabricated with 430 stainless steel and certified for over 5,000 pounds. Use over asphalt shingle, wood shake or metal roofing, the...

Bolt-on D-Ring Anchor with Installation Plate  Features: Forged D-ring and Bolt-on PlateProvides Simple Overhead Anchorage SolutionFor use on steel I-beams, columns and other steel structuresHeavy-duty steel construction2" x 4-1/2 plate with 1/2" holesComplies With ANSI Z359.18-2017  Features 2" x 4-1/2" alloy steel anchoring plate and D-ring1/2" bolt holes require user-supplied fasteners for fixed position installation.Complies with ANSI Z359.18-2017 Anchorage Location: Select...

This is a single sided D-ring anchorage device that are installed at the ridge, hip-ridge or in the field for permanent or temporary use. Permanent use anchors are supplied with stainless steel nail fasteners and a butyl strip flashing. The 8-1/2” length is idea for shingle type roofs allowing the anchor to be attached over the roofing material. The RS-10 is exactly ½ of our RetroFit anchor, making it an ideal complimentary anchor for hip ridges and shed roofs. Available with a “Dual Hole”...

The Guardian Fall Protection Ridge-It Anchor line is designed for use on wood rooftops. This Ridge-It model RIDG-1 is manufactured with a D-ring on one end and is 9—3/4" long, while the RIDG-2 is manufactured with 2 D-ring ends, and is 18" long. Ridge-It Anchors are composed highly durable stainless steel and zinc-plated steel, and are compliant with all applicable OSHA regulations. Ridge-It Anchors are easy to install, and are ideal for both residential construction and maintenance...

Tie-Off Straps are made from 2” wide polyester or nylon and are designed for use as temporary anchorage points to connect vertical lifelines, SRL’s, web lanyard and rope lanyards. Use on wood, steel and concrete structures. Tie-Off straps are wrapped, cinched around the structure to make for a secure anchor or can be embedded into concrete and evacuated when finished with the job. Please see the part number list below for Application, Length, Compliance and Packaging information for all our...

Weld-on D-Ring Anchor with Unplated Installation Plate Features: Forged D-ringPlain/Uncoated Steel Plate for Weld-on or Bolt-on ApplicationsCan be installed wherever weld-on applications are preferredProvides Simple Overhead Anchorage SolutionFor use on steel I-beams, columns and other steel structuresHeavy-duty steel construction2" x 4-1/2 plate with 1/2" holes Anchorage Location:  Select a suitable anchorage point that will support the strength requirement and minimize free fall and...

The easy-to-use 12048 scaffold brackets offer convenience for residential or commercial roofing projects. They are installed over wall sheathing just below the eave height on one or all four sides of a structure to create a safe, convenient walkway for erection of roof trusses, plywood, shingle, fascia, gutters, and under-eave covering. They include a 3/16" sway brace for right or left hand use and a 5/8" safety bolt and clip. The #12020 Plate Hanger may be used to hook the scaffold bracket...

The anchor can be installed as a retro/reroof application or in new construction on low- and high-profile tile and slate roofing material. This is a double D-ring anchor that measures 40” in between the D-rings which allows them be exposed just under the last course of tile. The unique design does not require a conventional flashing system because the anchor does not penetrate the sheeting. It installs with 8 spiral shank stainless steel nails and includes a butyl flashing strip to provide a...

The Guardian Fall Protection Beamer 2000 is a versatile Fall Arrest anchor designed for use both overhead and at foot level. Attachable to both steel I and H beams, the Beamer 2000 offers Nylon bushings to provide smooth movement along the beam, that also function as impact indicators in the event of a fall. This extremely durable anchor also includes a precision machined aluminum bar and ratcheting end pieces, which allow for quick and easy adjustment with just one hand. When used at foot...

Designed specifically for the Metal Building industry, our Super Z-Purlin provides an easy to install anchorage device that includes attachment bolts. The stem height of the anchor is compatible with high rib roofing panels and blanket type insulation. Waterproofing is achieved using a high quality E.P.D.M. gray colored flashing boot and matching stem cover that has an aluminum flange allowing it to be configured easily to any shape panel. The anchor stem features a collapsible design that...

Leading edge retractables (models with an attached shock absorber pack) are designed for use in applications to provide added protection against lifeline wear and/or cutting, when working near leading edges, where a fall may occur. This could include, but is not limited to, roofing or eaves, sheared, cold rolled, or cut steel, and edge work on concrete and various decking operations. USE CAUTION…..and provide additional protection against cutting (i.e. a heavy pad) over the exposed sharp edge....

Designed specifically for the Metal Building industry, our Super Z-Purlin provides an easy to install anchorage device that includes attachment bolts. The stem height of the anchor is compatible with high rib roofing panels and blanket type insulation. Waterproofing is achieved using a high quality E.P.D.M. gray colored flashing boot and matching stem cover that has an aluminum flange allowing it to be configured easily to any shape panel. The anchor stem features a collapsible design that...

The Guardian Fall Protection “Universal Guardrail Posts” are designed to work along with Guardian’s other guardrail mounting options. The product is composed of lightweight welded steel and installs easily into Guardian Fall Protection guardrail gusset mounts (15159 and 61027). The maximum spacing between each post is 8' apart.  Features: Installs easily into mountsAlso available in 52" & 74" size options (please call) Applicable Standards: OSHA 1910 & OSHA 1926 Subpart...

The Guardian Fall Protection Beamer 3000, the newest in our line of beam anchors, combines the many versatile features of the Beamer 2000 with some new innovations. The Beamer 3000 weighs 25% less than its predecessor, making it one of the lightest beam anchors available on the market. It also includes a dual adjustment feature that makes it even easier to adjust to its ideal position. No more unsnagging a connector or a lifeline when working at heights, the new and improved Beamer 3000...

This Toeboard attachment is a component of the Guardian Fall Protection Stacker Bracket System. Toeboards are required on all guardrail systems if there is any risk for equipment or materials to fall to a lower surface, and are always recommended. The Toeboard attachment fits to the Stacker Bracket Frame to allow for the safe and easy installation of toeboards. Features:  Attachment for hanging scaffolding Durable  Applicable Standards: OSHA 1910 & OSHA 1926 Subpart...

The Guardian Fall Protection Beamer 2000 is a versatile Fall Arrest anchor designed for use both overhead and at foot level. Attachable to both steel I and H beams, the Beamer 2000 offers Nylon bushings to provide smooth movement along the beam, that also function as impact indicators in the event of a fall. This extremely durable anchor also includes a precision machined aluminum bar and ratcheting end pieces, which allow for quick and easy adjustment with just one hand. When used at foot...