Residential Roofing

'The Work Horse', Devours Anything in its Path Removes: Asphalt, fiberglass, asbestos, slate, cedar and tin 48" Length The Blade: Wide-base hardened steel alloy grasps under more of the materials being removed thus allowing you to salvage reusable materials

RipBlade 5x is designed for cutting shingles and decking. It is the most versatile and the longest lasting. Each blade cuts over 9,000 linear feet without clogging and can be sharpened. What the RipBlade 5x cuts: 2 layers of shingles 2 layers of shingles and decking

55" length, 10 Teeth, General Purpose Tear-Off The Original Shingle Eater offers the best ergonomic design on the market, saving your back, time, and energy. Our rugged tools are designed to handle the demands of your asphalt roofing tear off projects. At roughly 7.4 lbs, this tool is lightweight. The 10" wide footplate allows you to snag 2 nails with each swipe, enabling a more efficient tear off. Regardless of your position (stand,sit, kneel), the 55" handle accommodates most conventional...

RipBlade 3x is designed for cutting flat roofs and multi-layer shingle roofs. Each blade cuts over 7,500 linear feet without clogging and can be sharpened. What the RipBlade 3x cuts: Tar & Gravel 3 Layers of shingles Multi-layer cap sheet

Introducing the new Double Dipper Shingle Remover! This shingle stripper will remove any stubborn shingle with ease. This Double Dipper Shingle Remover features the following: 20-inch wide serrated blade removes massive amounts of shingles2 steel handles with poly D-grips for 2-handed strippingSimple and strong design Lightweight - Only 13 pounds! 48 inches of overall length Assembly Required* ...

46.5" length, 10 teeth for Steeper Pitched Roofs and Men Under 6 feetDesigned specifically for Steeper Pitched Roofs and Roofers under 6 feet. Same 10" wide footplate as "The Original" that wears evenly, grabbing 2 nails with each swipe so you don't have to go back over the roof with a hammer to pull out nails. Accommodates all conventional asphalt tear-offs. OSHA Safety Yellow. 100% American Made.

For use with a sound 2 x 6" plank. Place Brackets no more than 8 feet apart. Use all 4 nail slots. Capacity is one worker plus 40 lbs. of materials per 4' of scaffolding. Steel roof bracket for various pitches and plank sizes. 4 offset nail slots and back-stiffening rib to eliminate twists and flexing. Smooth edges and rounded corners will not cut hands or work area. Easy installation and removal without damaging shingles. DO NOT OVERLOAD! FEATURES For use with various pitches and plank...

The Johnny Jack Offset Roof bracket provides a walking surface on steep pitch roofs during installation of interlocking roofing materials such as metal shingles, tile, and other systems. A seven foot flat bar connects the walking plank bracket at the bottom with the nail slots at the top; features 5 ½ inch surface clearance. Used to install interlocking shingles where standard roof brackets cannot be used. FEATURES JohnnyJack’s design provides a better platform for staging materials on...

For use with a sound 2 x 6" plank. Place Brackets no more than 8 feet apart. Use all 4 nail slots. Capacity is one worker plus 40 lbs. of materials per 4' of scaffolding. DO NOT OVERLOAD! FEATURES For use with various pitches and plank sizes 4 offset nail slots (OSHA requires 3) that will not allow the bracket to slide up 6 long welds for strength Back-stiffening rib to eliminate twisting and flexing  Smooth edges and round corners that will not cut hands or work area Easy to set up,...

Features: 6-position locking adjustmentsConstructed of heavy duty galvanized steel10” platformCan be repositioned & taken down without damaging shinglesFolds flat for convenient storage and transportReplaceable 3-position tongueCapacity: 1 worker plus 40 lbs. per 8’ stagingMaximum 8’ spacing between bracket5/ Case

23" Length, 4 teeth for Flashing and Tight areas, Around SkylightsThe Shingle Eater Junior is recommended for for roofing renovation in tight areas around skylights or chimneys, valleys where peaks meet. Lightweight, durable, high quality steel. It is lightweight, easy to use while up on a ladder ripping off gutters or flashing. The Junior is our second best-selling tool, used for roofing renovation, remodeling. OSHA Safety Yellow. 100% American Made.

For use with a sound 2 x 4" plank. Place Brackets no more than 8 feet apart. Use all 4 nail slots. Capacity is one worker plus 40 lbs. of materials per 4' of scaffolding. Steel roof bracket for various pitches and plank sizes. 4 offset nail slots and back-stiffening rib to eliminate twists and flexing. Smooth edges and rounded corners will not cut hands or work area. Easy installation and removal without damaging shingles. DO NOT OVERLOAD! FEATURES For use with various pitches and...

For use with a sound 2 x 6" plank. Place Brackets no more than 8 feet apart. Use all 4 nail slots. Capacity is one worker plus 40 lbs. of materials per 4' of scaffolding. Steel roof bracket for various pitches and plank sizes. 4 offset nail slots and back-stiffening rib to eliminate twists and flexing. Smooth edges and rounded corners will not cut hands or work area. Easy installation and removal without damaging shingles. DO NOT OVERLOAD! FEATURES For use with various pitches and plank...

For use with a sound 2 x 4"or 2 x 6" plank. Place Brackets no more than 8 feet apart. Use all 4 nail slots. Capacity is one worker plus 40 lbs. of materials per 4' of scaffolding. DO NOT OVERLOAD! FEATURES For use with various pitches and plank sizes 4 offset nail slots (OSHA requires 3) that will not allow the bracket to slide up 6 long welds for strength Back-stiffening rib to eliminate twisting and flexing  Smooth edges and round corners that will not cut hands or work area Easy to set...

8126 - Renovator 90 Tall Demo Roof Tear Off Tool8126 Large Demo Eater was recently developed to fill the gap for more serious roofing projects, as well as interior demolition. The 55" angled handle and 10" footplate make it most similar to our best-selling Shingle Eater 6126. What sets this tool apart is the footplate welded at a 90 degree angle which provides a striking/kicking surface, and footplate reinforced with welded gussets for additional prying power.Because of our product...

36.5" length, 7 Teeth for Steep and Hard To Work AreasIf you're working on a small garage, a steep peak, or difficult areas near the ridge or edge or between peaks, the smaller 7" footplate is often easier to manipulate. This tool also works well for removing gutters and downspouts. Still has the beveled teeth and corrugations on the footplate, but the shorter handle and longer, narrower foot are more easily used for specialty tear-offs. OSHA Safety Yellow. 100% American Made. ...

For use with a sound 2 x 6" plank. Place Brackets no more than 8 feet apart. Use all 4 nail slots. Capacity is one worker plus 40 lbs. of materials per 4' of scaffolding. Steel roof bracket for various pitches and plank sizes. 4 offset nail slots and back-stiffening rib to eliminate twists and flexing. Smooth edges and rounded corners will not cut hands or work area. Easy installation and removal without damaging shingles. DO NOT OVERLOAD! FEATURES For use with various pitches and plank...

46.5" length, 10" Footplate, General Purpose Tool This version most closely resembles the 6127 tool, a better length for roofers under 6 feet. The entire D handle is made of steel, easy for gripping, and adds only about 1/2 lb to the overall weight of the tool. It is well-balanced and will slide easily under shingles. Smooth finish, no sharp angles, and comfortable. We worked for over 2 years to get the design right on the D Handle, and so far, roofers have been impressed with our workmanship....

RACE-RB-ADJ, 10” x 30°/45°/60°/90° ADJUSTABLE ROOFING BRACKET CAPACITY: One worker per 8 feet of scaffolding or up to 250 pounds of materials - No more than one person shall occupy any given 8 feet of a Roofing Bracket Scaffold - Use the walking surface to stage material and ease working on steep slope roofs. - Always use OSHA compliant fall arrest system, guardrails, catch platforms or other safety equip­ment as required by Local, State or Federal OSHA Regulation - Roof Brackets are intended...

Our customers are growing attached to the D handled version of our 6127 tool, and we've had multiple requests for a Demo Eater D handled. We're introducing the 8130 D handled version of the 8126 tool. They are individually made, so lengths may vary up to 1".Because of our product improvements, many roofers are considering these models the "new and improved" Shingle Eater. This multipurpose tool is perfect for remodeling or renovation projects. It does weigh close to 8 1/2 lbs due to the...

For use with a sound 2 x 8" plank. Place Brackets no more than 8 feet apart. Use all 4 nail slots. Capacity is one worker plus 40 lbs. of materials per 4' of scaffolding. Steel roof bracket for various pitches and plank sizes. 4 offset nail slots and back-stiffening rib to eliminate twists and flexing. Smooth edges and rounded corners will not cut hands or work area. Easy installation and removal without damaging shingles. DO NOT OVERLOAD! FEATURES For use with various pitches and plank...

For use with a sound 2 x 8" plank. Place Brackets no more than 8 feet apart. Use all 4 nail slots. Capacity is one worker plus 40 lbs. of materials per 4' of scaffolding. DO NOT OVERLOAD! FEATURES For use with various pitches and plank sizes 4 offset nail slots (OSHA requires 3) that will not allow the bracket to slide up 6 long welds for strength Back-stiffening rib to eliminate twisting and flexing Smooth edges and round corners that will not cut hands or work area Easy to set up, operate,...

For use with a sound 2 x 10" plank. Place Brackets no more than 8 feet apart. Use all 4 nail slots. Capacity is one worker plus 40 lbs. of materials per 4' of scaffolding. Steel roof bracket for various pitches and plank sizes. 4 offset nail slots and back-stiffening rib to eliminate twists and flexing. Smooth edges and rounded corners will not cut hands or work area. Easy installation and removal without damaging shingles. DO NOT OVERLOAD! FEATURES For use with various pitches and plank...

For use with a sound 2 x 4" plank. Place Brackets no more than 8 feet apart. Use all 4 nail slots. Capacity is one worker plus 40 lbs. of materials per 4' of scaffolding. Steel roof bracket for various pitches and plank sizes. 4 offset nail slots and back-stiffening rib to eliminate twists and flexing. Smooth edges and rounded corners will not cut hands or work area. Easy installation and removal without damaging shingles. DO NOT OVERLOAD! FEATURES For use with various pitches and plank...

RACE-RB-F-6-90, 2" X 6” x 90° x 18" long FIXED ROOFING BRACKET On roofs with a 4/12 to 6/12 roof pitch, when in­stalled as a slide guard, the scaffold brackets should provide a platform that is 90 degrees to the roof’s sur­face at a point along the eave of the roof. For roof slopes greater than 6/ 12 up to 8/12 additional 90-degree slide guards must be installed par­allel to the first row no further than every eight feet of roof slope. Ad­ditional fall protection methods are required...

RACE-RB-F-8-45, 8” x 45°x 19" long FIXED ROOFING BRACKET, FOR USE ON 12/12 PITCH ROOFS. CAPACITY: One worker per 8 feet of scaffolding or up to 250 pounds of materials - Only for use on roofs - Always use fall protection in accordance with local, state and federal OSHA regulations - Not an anchor point - Roof brackets are meant for use by experienced tradesmen having full knowledge in its use - OSHA regulations require that the employer provide training in the use and care of this product ...